Skip to content

press brake

Hydraulic CNC bending machine main configuration-The main seals of the oil cylinder are produced by Japan Huarka Company

Hydraulic CNC bending machine main configuration: 1. The main seals of the oil cylinder are produced by Japan Huarka Company. 2. The main parts in the electric box are produced by Schneider in France. 3. The hydraulic system is controlled by cartridge valve, and the main hydraulic components are made by Germany Hoerbiger Company. 4, the hydraulic pump adopts aerospace standard low noise internal gear pump. 5. The oil cylinder processed by the manufacturer and the sealing ring imported in… Read More »Hydraulic CNC bending machine main configuration-The main seals of the oil cylinder are produced by Japan Huarka Company

CNC bending machine boot before you do a good job of preparation work?

Before starting the CNC bending machine, we must first connect the power supply, open the switch on the control panel, and then start the oil pump, so that you can hear the sound of the oil pump rotation (the machine does not act at this time). Preparation before startup: (1) Guide rail, rear stopper and other moving parts for centralized oil supply should be refueled regularly; (2) Check mold cleaning and damage, and deal with abnormality in time; (3) Check… Read More »CNC bending machine boot before you do a good job of preparation work?

The safe operation rules of steel bending machines are as follows

The operator should operate in strict accordance with the safe operation rules of the bending machine. If any abnormality is found in the operation process, the operator should stop the operation immediately and stop the machine to check the reason. The safe operation rules of steel bending machines are as follows: 1. Strictly abide by the safe operation rules of machine tool workers, and wear labor protection equipment according to the provisions. 2. The upper and lower molds should be… Read More »The safe operation rules of steel bending machines are as follows

Notes for the operation of two-roll plate rolling machine

Notes for the operation of two-roll plate rolling machine Two-roll plate bending machine is a common mechanical equipment, in the case of improper operation, it is easy to happen accidents, resulting in tragedy.In the process of operating the two-roll rolling machine, Wuxi two-roll rolling machine, we must pay attention to the following points, in order to work in the two-roll rolling machine staff safety. 1, workers in the use of rolling machine before must pass special training, skilled operation can… Read More »Notes for the operation of two-roll plate rolling machine

WC67Y-100T/3200 hydraulic plate bending machine Product shape and structure

WC67Y-100T/3200 hydraulic plate bending machine Product shape and structure 1. UG (finite element) analysis method, computer aided optimization design, beautiful appearance. 2. The machine adopts steel plate welding structure, with sufficient strength and stiffness, hydraulic transmission to ensure that the work will not be caused by the thickness of the plate or the lower die "V" shaped groove improper selection of serious overload accidents, in addition to the machine has the characteristics of smooth work, convenient operation, low noise, safety… Read More »WC67Y-100T/3200 hydraulic plate bending machine Product shape and structure

4-Roller Plate Bending Machine-The precision of products is superior

4-Roller Plate Bending Machine When the end is prebent, the length of the straight edge can be set freely, and the upper roller is pressed down. Under a certain pressure, the high precision end prebending can be implemented. The precision of products is superior Due to continuous bending and high precision end prebending, products with superior precision are obtained.In addition, the upper roller is in the shape of a drum, and the supporting roller is adjusted to make ideal products… Read More »4-Roller Plate Bending Machine-The precision of products is superior

hydraulic numerical control bending machine mold processing Q235

The CNC bending machine mold includes a bracket, a work table and a clamping plate. When used, the wire is electrified on the coil, and the power is generated on the pressing plate, so as to realize the clamping of the thin plate between the pressing plate and the base.  hydraulic numerical control bending machine mold processing Q235 sheet material to do a brief introduction: 1. First, switch on the power supply, turn on the switch on the control panel,… Read More »hydraulic numerical control bending machine mold processing Q235

Cnc hydraulic press brake Performance and work slider

I. Cnc hydraulic press brake Performance and characteristics 1. Hydraulic transmission to ensure that the work will not change due to the thickness of the plate, in addition, the machine has the characteristics of smooth work, convenient operation, low noise, safety and reliability. 2. The cylinder is equipped with a mechanical block to ensure the repeated positioning accuracy of the sliding block to the bottom dead point, so as to ensure the consistency of the bending Angle during mass production.… Read More »Cnc hydraulic press brake Performance and work slider

W10 two-rolling machine the product description

W10 two-rolling machine the product description 1. It can meet the requirements of 0.3mm-6mm all kinds of metal sheets for round forming at one time, bringing unprecedented precision of wire meter round. 2.width up to 3000mm, the use of EPS automatic leveling technology, automatic adjustment of two axes parallel, eliminate the horn shaped workpiece. 3. automatic one - time coiling, high coiling efficiency, single machine can reach more than 400 pieces per day. 4. perfect arc, joint without obvious straight… Read More »W10 two-rolling machine the product description

Application and field of cnc press brake machine bending

Application and field of cnc press brake machine bending 1. Pipe for piping.Such as: water, gas pipe, steam pipe with seamless pipe, oil delivery pipe, oil and natural gas trunk line with pipe.Agricultural irrigation water faucet with pipe and sprinkler irrigation pipe. 2. Pipe for thermal equipment.Such as - boiler with boiling water pipe, superheated steam pipe, locomotive boiler superheated pipe, small smoke pipe, arch brick pipe and high temperature and high pressure boiler pipe. 3. Pipe for mechanical industry.Such… Read More »Application and field of cnc press brake machine bending

en_USEnglish
ru_RURussian es_ESSpanish pt_PTPortuguese en_USEnglish
WeCreativez WhatsApp Support
Our customer support team is here to answer your questions. Ask us anything!
👋 Hi, how can I help?
Hi, how can I help?

Contact Us

Fill out the information below to get a free quote and we will get back to you within 24 hours！