press brake

WC67Y-40T/2500 hydraulic bending machine structure characteristics: Slider part: hydraulic transmission, slider part is composed of slider, cylinder and mechanical stopper fine tuning structure. The left and right cylinder is fixed on the frame, the piston (rod) drives the slider up and down through the hydraulic pressure, and the mechanical block is controlled by the numerical control system to adjust the numerical value; Worktable part: by the button box operation, the motor drive the block frame move before and after, and… Read More »WC67Y-40T/2500 hydraulic bending machine structure characteristics

A brief introduction to WC67Y-40/2500 hydraulic bending machine WC67Y-40/2500 hydraulic bending machine is a kind of widely used plate bending equipment,with a very simple general mold for plate bending a variety of angles of the straight line, simple operation, good versatility, low mold cost, convenient replacement, the machine itself only one basic movement -- up and down reciprocating straight line movement. Two, the main structure and working principle of WC67Y-40/2500 hydraulic bending machine: 1. Main structure of the machine The… Read More »A brief introduction to WC67Y-40/2500 hydraulic bending machine

During the first test run, the electric unit of oil pump should be started for empty operation first, and then the movement of the nc hydraulic press brake should be tested by "inching". Then test the "single" and "continuous" movements, the sliding block stroke and the rear stopper control functions. When the machine is proved to be in normal operation, the following procedures can be followed. 1. According to the thickness of the plate and the length of the folded… Read More »Precautions and operation steps of nc hydraulic press brake before test run

Bending machine special CNC system CNC-600, through the servo motor (can also be equipped with frequency converter and encoder control), to control the Y axis and X axis (that is, the positioning of the height of the baffle and the movement of the rear baffle before and after). 1. Choose 320* 128-LCD to display high brightness blue display. Full Chinese large font display; 2. Convenient switching between Chinese and English; 3. Angle programming (5°-179°); 4. Mold parameter setting; 5. Angle… Read More »WE67K-100T~500T series of large electro - hydraulic synchronous sheet bending machine

WC67Y-63/2500 hydraulic plate bending machine Performance and features: All steel welded structure, vibration stress relief, high mechanical strength, good rigidity, hydraulic up transmission, stable and reliable; Mechanical block, torque shaft synchronization, high precision. Distance of rear stopper, stroke of upper slider, electric adjustment, manual fine adjustment device, digital display; The upper die is equipped with a deflection compensation mechanism, and the lower deflection compensation mechanism can be used for machines with a length of 250 tons and over 4000mm. WC67Y-63/2500… Read More »WC67Y-63/2500 hydraulic plate bending machine Performance and features

Brief introduction of Durmapress NC38 Pipe bending machine : 1: Mechanical transmission part: the gear transmission, durable, strong strength, bending process wheel rotation, with high strength laminating one-time shaped bending pipe. 2: Circuit control part: using embedded microcomputer intelligent control system control, Angle input to achieve digital, easy to use. 3. Product Advantages: ①: made by experienced technical personnel, stable performance ②: Intelligent chip control, fast response speed, high sensitivity, intelligent control system can be set.③: The encoder is used… Read More »Brief introduction of Durmapress NC38 Pipe bending machine

I. WC67Y-400T6000 hydraulic plate bending machine  Structure of the whole machine The machine adopts the whole machine welding structure, the frame is composed of left and right wall panels, work table, oil tank, brace, synchronous shaft and slide block, etc. II. Technology and process 1, Integrated hydraulic control system, compact structure, reduce the pipeline connection, improve the reliability and maintainability of the system. 2, the use of torsional shaft synchronization, at both ends of the slider is equipped with two… Read More »WC67Y-400T6000 hydraulic plate bending machine Structure of the whole machine

Mold operation instructions for machines hydraulic press brake 1. Before calendering, we should first reflect on whether the two rolls of the bending machine mold can be parallel. If not, adjust the gasket to make it parallel.And confirm the appearance of the drum clean, no accessories.Then, reflect on whether the two rolls are complete and close, Zhejiang stainless steel bending machine mold, press the pointer reading can be zero, if not zero, adjust the pointer scale to zero. 2. Adjust… Read More »Mold operation instructions for machines hydraulic press brake